Effect of partial replacement of geopolymer binder materials on the fresh and mechanical properties: A review

The growth of demand for concrete raises concerns about the consumption of natural resources and ordinary Portland cement. Geopolymer composites show promise as a sustainable alternative for conventional cement concrete. Considering the wide range of potential geopolymer composites applications (including suitability for transportation infrastructure, underwater applications, repair and rehabilitation of structures as well as recent developments in 3D printing), the desired fresh and mechanical properties of the geopolymer composite may vary between applications: for example, rapid setting can be a merit for certain applications and a demerit for others. Therefore, the desired fresh and mechanical properties (e.g., workability, setting time, compressive strength, etc.) can be controlled for a given geopolymer source material through its partial substitution by natural or by-product materials. Recognizing the critical role of various replacement materials in enhancing the potential applications of geopolymer composites, the present review was undertaken to quantify and understand the effect of partial replacement by fly ash, metakaolin, kaolin, red mud, slag, ordinary Portland cement, and silica fume on the setting time, workability, compressive strength and flexural strength of various source materials addressed in the literature. The review also provides insights into research gaps in the field to promote future research.     

一种X煤在首钢的应用实践

针对当前优质炼焦煤资源越来越少，而高炉生产对焦炭质量指标要求越来越高的情况下，对具有低灰、高硫特点的X煤进行了系统的炼焦试验研究。结果发现，在炼焦生产中合理配加5%～8%的X煤不会造成焦炭硫分升高的不利影响，焦炭灰分下降明显，强度保持稳定。该研究成果成功应用于首钢炼焦生产，焦炭各项指标均达标，这不仅扩大了炼焦煤的使用范围，而且在资源使用方面为公司焦炭灰分的降低提供了支持。     

Performance characteristics of concrete based on a ternary calcium sulfoaluminate–anhydrite–fly ash cement

This paper reports an assessment of the performance of concrete based on a calcium sulfoaluminate–anhydrite–fly ash cement combination. Concretes were prepared at three different w/c ratios and the properties were compared to those of Portland cement and blast-furnace cement concretes. The assessment involved determination of mechanical and durability properties. The results suggest that an advantageous synergistic effect between and ettringite and fly ash (Ioannou et al., 2014) was reflected in the concrete’s low water absorption rates, high sulfate resistance, and low chloride diffusion coefficients. However, carbonation depths, considering the dense ettringite-rich microstructure developed, were higher than those observed in Portland cement concretes at a given w/c ratio. It was concluded that the amount of alkali hydroxides present in the pore solution is as important factor as the w/c ratio when performance of this type of concrete is addressed.     

大宗粉煤灰的综合利用及提质方案

对于大宗粉煤灰原灰进行分选加球磨机粉磨，同时添加合适的激发剂进行提质，可以生产出不同细度和活性的粉煤灰产品，提升粉煤灰在水泥及商品砼中的用量。介绍了某发电公司的粉煤灰处置现状，在此基础上，对商品砼的粉煤灰性能要求进行了大量市场调研，针对性地给出了该公司粉煤灰的提质方案，最后进行了提质粉煤灰的应用市场和产品竞争力分析。     

云冈矿采空区自然发火综合治理技术实践

针对云冈矿12#煤层8820、8822采空区出现CO泄漏事件,采用粉煤灰填充,构筑木板墙充填粉煤灰,配以墙体周边注马丽散堵漏;采用灌浆泵进行地面黄土灌浆,实施采空区灭火。通过对采空区自然发火进行综合治理,取得了良好效果,消除了自然发火隐患。     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

烧结时间对含铅玻璃制备微晶玻璃析晶及性能的影响

以铅玻璃与粉煤灰为原料，通过协同熔炼制备了微晶玻璃。通过XRD和SEM等手段研究了不同烧结时间下微晶玻璃的物相组成及显微结构，测定了微晶玻璃的密度、吸水率、维氏硬度和化学抗性。结果表明: 延长烧结时间对含铅玻璃加入量为40%(FG40)、50%(FG50)样品的晶相类型和晶化程度有影响，而对含铅玻璃加入量为60%(FG60)、70%(FG70)和80%(FG80)样品的影响较小。随着烧结时间延长，样品晶化程度提高，晶体长大，玻璃相减少。适宜的含铅玻璃加入量为50%~70%，对应的FG50、FG60、FG70样品最佳烧结时间分别为4 h、3 h、3 h。     

350MW机组锅炉SCR脱硝系统优化

准东煤田是我国目前最大的整装煤田,但准东煤在锅炉燃烧过程中易发生结焦问题,一般掺烧高岭土缓解结焦。某燃用准东煤350 MW机组,锅炉燃煤掺烧高岭土后烟气携带灰尘颗粒及灰尘量增大,出现SCR脱硝系统烟道积灰严重和喷氨量明显偏大问题,同时在空气预热器形成硫酸氢氨堵塞,使机组不能长周期稳定运行。通过与国内同类型多台机组锅炉对比后发现,脱硝系统均存在易产生积灰的脱硝转向室、催化剂上方及空气预热器入口斜坡积灰状况等情况。针对存在的问题,通过建立改造前、后的模型计算分析,进行了导流板布置的优化设计、CFD流场分布、优化SCR系统导流板设计、声波与蒸汽吹灰器结合吹灰和氨注射栅格优化升级等工作,应用德图480风速仪实测风速试验,发现脱硝烟道原导流板设计不合理及施工安装偏差;原导流板水平段跨距大,支撑不足,造成导流板压塌变形,影响烟气流场分布;锅炉所烧煤质为高钠煤,为防止锅炉结焦掺烧高岭土后,增加了烟气飞灰颗粒及灰尘量,飞灰具有很大黏性,易沉积在烟道导流板及烟道壁面上。因此,提出对脱硝内部各处导流板进行优化改造,对脱硝系统烟道易产生积灰的部位增加声波吹灰器,对喷氨格栅喷嘴数量及氨空混合器升级,同时开展锅炉SCR脱硝喷氨热态优化调整试验工作。通过开展相关工作,SCR烟气系统的烟气流场相对标准偏差优化5%,相同负荷下液氨消耗量降低45%,彻底解决脱硝系统积灰和空气预热器堵塞问题,实现机组满负荷达标稳定运行。锅炉长期运行半年后停炉检查,发现前期脱硝系统烟道高达1 m的积灰部位彻底解决,催化剂表面干净无杂物,解决了脱硝系统积灰问题,同时配合提高空气预热器冷端综合温度的措施,彻底解决锅炉空气预热器堵塞问题。同时,经济效益显著,每年可以分别节约液氨费用70万元,节约风机电耗费用100万元,节约检修清理积灰及检修费用80万元,节约空气预热器冲洗治理费用20万元,综合节约费用270万元/a,达到预期效果实现机组长周期安全经济稳定运行。     

不同粒径改性粉煤灰对磷酸根吸附性能的影响

废水排放过量的磷导致水体污染日益严重，将粉煤灰通过化学改性制备成了水化硅酸钙吸附剂，研究了改性吸附剂对磷酸根的吸附效果。利用XRD, SEM及BET比表面积等手段对粒度分级前后的吸附剂进行表征，研究不同粒级吸附剂对磷酸根的吸附性能，并考察其吸附机理。结果表明，不同粒级的吸附剂其化学成分出现了明显的偏析现象，孔隙结构也差异显著。相比其他粒径下的吸附剂颗粒，颗粒粒径在50?75 μm时，吸附剂中钙和硅含量较多，铝、铁和镁含量较低，水化硅酸钙组分含量最高，且伴有含铝的托贝莫来石晶体出现，钙离子的增加使其可以与更多的磷酸根结合形成沉淀。同时此粒径下具有较高的比表面积及孔隙度，疏松多孔的结构为钙离子提供更多活性位点。当使用粒径在50?75 μm的吸附剂吸附磷酸根时，磷的饱和吸附量可达到17.1 mg/g，比未分级的吸附剂高19.58%。     

Design and synthesis of foam glasses from recycled materials

Recycling has emerged as an environmental key point due to the diminishing of natural resources and the generation of ever-increasing amounts of industrial solid wastes. Glass wastes are among the materials that attract great interest in the recycling concept. This work presents the results of foams production from four series of compositions. The first series comprises powders of a sodium-calcium-silicate sheet glass cullet as the main component, an alkali-earth aluminosilicate glass as an additive, and a reagent grade silicon carbide (SiC) powder as gassing agent. In the second series, the glass cullet was used in combination with fly ashes (FLA) as main components, while SiC waste from abrasive paper served as foaming agent. In the third and fourth series, carbonates (calcite and dolomite) were used for foaming powder mixtures composed of sheet glass cullet and FLA, and powdered cathode ray tube panel glasses, respectively. All the processing parameters, including the main components, the nature and content of foaming agents are shown to play a crucial role on the foaming ability and final properties of the glass foams.